CALMAX

  • Colour Code    
 White / Violet
  • Typical Analysis
C
 0,60
       Mn     
 0,8 
       Cr      
 4,5
           Mo         
 0,5
        V        
 0,2
         Si        
 0,35
        Others
 --
  • Hardness Supplied approx.HB
  200
  • Standards
       AISI (USA)    --
       W.nr (Germany) 
  1.2358
       JIS (Japan) 
  --
  • Characteristics  
  A very versatile high alloyed steel with good wear resistance & high  toughness.
  • Soft Anneal ºC
 860
  • Hardening Temp.ºC
  950-970
  • Quenching 
  Oil, Vacuum, air
Tempering temperature ºC 2x2 hrs
Hardness achieved ( HRC )
200
 59
250
 58
400
 54
500
 53
550

 50
600
 43
  • Application 
  General blanking & forming, deep drawing, coining & cold extrusion dies.
                              
HOLDAX
  • Colour Code    
 Yellow / Blue
  • Typical Analysis
C
 0,40
       Mn     
 1,5
       Cr      
 1,9
           Mo         
 0,2
        V        
 --
         Si        
 0,4
        Others
 0,07
  • Hardness Supplied approx.HB
  310
  • Standards
       AISI (USA)    --
       W.nr (Germany) 
  1.2312
       JIS (Japan) 
  --
  • Characteristics  
  Prehardened steel for holder blocks with very good machinabily.
  • Soft Anneal ºC
 700
  • Hardening
    Temp.    ºC
  in as-del.cond.
  • Quenching 
  --
Tempering temperature ºC 2x2 hrs
Hardness achieved ( HRC )
200
 --
250
 --
400
 --
500
 --
550
 --
600
 --
  • Application 
  For holding core and cavity of mould and die.

IMPAX SUPREME
  • Colour Code    
 Yellow / Green
  • Typical Analysis
C
 0,37
       Mn     
 1,4
       Cr      
 2,0
           Mo         
 0,2
        V        
  --
         Si        
 0,3
        Others
 max 0,01
  • Hardness Supplied approx.HB
  310
  • Standards
       AISI (USA)    P20 Modified
       W.nr (Germany) 
  1.2738
       JIS (Japan) 
  --
  • Characteristics  
  Prehardened plastic mould steel, very good polishability & good  machinabily.
  • Soft Anneal ºC
 700
  • Hardening Temp.ºC
  --
  • Quenching 
  --
Tempering temperature ºC 2x2 hrs
Hardness achieved ( HRC )
200
 --
250
 --
400
 --
500
 --
550
 --
600

 --
  • Application 
  For injection moulds of thermoplastics.  Rubber moulds, extraction dies with  good polishability and photo-etching properties.

ORVAR SUPREME

  • Colour Code    
 Orange
  • Typical Analysis
C
 0,39
       Mn     
 0,4
       Cr      
 5,2
           Mo         
 1,4
        V        
 0,9
         Si        
 1,0
        Others
 0,003
  • Hardness Supplied approx.HB
  180
  • Standards
       AISI (USA)    Improved
       W.nr (Germany) 
  1.2344
       JIS (Japan) 
  SKD 61
  • Characteristics  
  A very versatile high alloyed steel with good wear resistance & high  toughness.
  • Soft Anneal ºC
 850
  • Hardening
    Temp.    ºC
  1020-1050
  • Quenching 
  Oil, Vacuum, air
Tempering temperature ºC 2x2 hrs
Hardness achieved ( HRC )
200
 52
250
 52
400
 53
500
 54
550

 52
600
 46
  • Application 
  General blanking & forming, deep drawing, coining & cold extrusion  dies.

RAMAX 2

  • Colour Code    
 Black / Brown with white line across
  • Typical Analysis
C
 0,12
       Mn     
 1,3
       Cr      
 13,4
           Mo         
 0,5
        V        
 0,20
         Si        
 0,20
        Others
 Ni 1,60
  • Hardness Supplied approx.HB
  350
  • Standards
       AISI (USA)    PATENTED GRADE
       W.nr (Germany) 
  PATENTED GRADE
       JIS (Japan) 
  PATENTED GRADE
  • Characteristics  
  Prehardened stainless steel with excellent machinability, corrosion  resistance and good indentation resistance.
  • Soft Anneal ºC
 PRE HARDENED STAINLESS MOULD  STEEL
  • Hardening Temp.ºC
  PRE HARDENED STAINLESS MOULD  STEEL 
  • Quenching 
  PRE HARDENED STAINLESS MOULD  STEEL
Tempering temperature ºC 2x2 hrs
Hardness achieved ( HRC )
200
 --
 300
 --
 560
 --
 600
 --
  • Application
  For moulding rubber and corrosion resistance material like PVC, and as dies for constructional parts.

CORRAX

  • Colour Code    
 Black / Grey
  • Typical Analysis
C
 0,03
       Mn     
 0,3
       Cr      
 12,0
           Mo         
 1,4
        V        
  --
         Si        
 0,3
        Others
 1,6
  • Hardness Supplied approx.HB
  330
  • Standards
       AISI (USA)    --
       W.nr (Germany) 
  --
       JIS (Japan) 
  --
  • Characteristics  
  A precipitation hardening steel with extremely good  corrosion resistance.
  • Soft Anneal ºC
 --
  • Hardening Temp.ºC
  Solution treat. 850
  • Quenching 
  Air
Tempering temperature ºC 2x2 hrs
Hardness achieved ( HRC )
200
 --
250
 --
400
 --
500
 --
550

 --
600
 --
  • Application 
  Injection moulds and extrusion for corrosive plastics.

STAVAX SUPREME

  • Colour Code    
 Orange/ Black with white line across
  • Typical Analysis
C
 0,24
       Mn     
 0,5
       Cr      
 13,3
           Mo         
  0,35
        V        
 0,35
         Si        
 0,3
        Others
 Ni 1,40
  • Hardness Supplied approx.HB
  250
  • Standards
       AISI (USA)    420 Modified & improvised
       W.nr (Germany) 
  1.2083 Modified & improvised
       JIS (Japan) 
  --
  • Characteristics  
  A through hardening corrosion resistance mould steel with excellent  polishability, wear resistance, good hardenability & toughness.
  • Soft Anneal ºC
 740
  • Hardening Temp.ºC
  1000-1025
  • Quenching 
  Oil, Vacuum Air, Vacuume
Tempering temperature ºC 2x2 hrs
Hardness achieved ( HRC )
200
        50
 300
        49
 560
        52
 600
        42
  • Application 

 For moulding optical/medical or transparent  parts, corrosive and re-inforced  plastics,  long run moulds with mirror polish of  1- micron levels.

POLMAX

  • Colour Code    
 Green / Black
  • Typical Analysis
C
 0.38
       Mn     
 0.5
       Cr      
 13.6
           Mo         
  --
        V        
 0.3
         Si        
 0.9
        Others
 --
  • Hardness Supplied approx.HB
  200
  • Standards
       AISI (USA)    PATENTED GRADE
       W.nr (Germany) 
  PATENTED GRADE
       JIS (Japan) 
  PATENTED GRADE
  • Characteristics  
  Excellent polishability. Mould steel with good corrosion resistance, wear  resistance & stability in
  hardening.
  • Soft Anneal ºC
 780
  • Hardening Temp.ºC
  1020-1030
  • Quenching 
  Oil, Vacuum Air, Vacuume
Tempering temperature ºC 2x2 hrs
Hardness achieved ( HRC )
200
      53
 300
      52
 560
      54
 600
      45
  • Application 

 A premium high polishability steel with good resistance suitable for moulding  compact discs lens medical equipments, etc…

 

PRODAX / ALUMEC

  • Colour Code    
 High strength aluminium alloy
  • Typical Analysis
C
 High strength aluminium alloy
       Mn     
 High strength aluminium alloy
       Cr      
 High strength aluminium alloy
           Mo         
  High strength aluminium alloy
        V        
 High strength aluminium alloy
         Si        
 High strength aluminium alloy
        Others
 High strength aluminium alloy
  • Hardness Supplied approx.HB
  164-168
  • Standards
       AISI (USA)    --
       W.nr (Germany) 
  --
       JIS (Japan) 
  --
  • Characteristics  
  Low weight with high thermal conductivy.
  • Soft Anneal ºC
 --
  • Hardening Temp.ºC
  --
  • Quenching 
  --
Tempering temperature ºC 2x2 hrs
Hardness achieved ( HRC )
200
 --
 300
 --
 560
 --
 600
 --
  • Application 

 Aluminium of plastic moulds, blow moulding and vacuum moulding.

MOLDMAX

  • Colour Code    
 Beryllium copper
  • Typical Analysis
C
 Beryllium copper
       Mn     
 Beryllium copper
       Cr      
 Beryllium copper
           Mo         
  Beryllium copper
        V        
 Beryllium copper
         Si        
 Beryllium copper
        Others
 Beryllium copper
  • Hardness Supplied approx.HB
  30HRC&40HRC
  • Standards
       AISI (USA)    --
       W.nr (Germany) 
  --
       JIS (Japan) 
  --
  • Characteristics  
  Beryllium copper for Plastics moulds.  Excellent Heat Conductivity.
  • Soft Anneal ºC
 --
  • Hardening Temp.ºC
  --
  • Quenching 
  --
Tempering temperature ºC 2x2 hrs
Hardness achieved ( HRC )
200
 --
 300
 --
 560
 --
 600
 --
  • Application 

 For plastic injection moulds & mould inserts where high emphasis is given  for lowest cycle time.

STAVAX ESR
  • Colour Code    
 Orange/ Black
  • Typical Analysis
C
 0,38
       Mn     
 0,5
       Cr      
 13,6
        V        
 0,3
         Si        
 0,9
  • Hardness Supplied approx.HB
  250
  • Standards
       AISI (USA)    420 Modified & improvised
       W.nr (Germany) 
  1.2083 Modified & improvised
       JIS (Japan) 
  --
  • Characteristics  
  A through hardening corrosion resistance mould steel with excellent  polishability, wear resistance, good hardenability & toughness.
  • Soft Anneal ºC
 740
  • Hardening Temp.ºC
  1020-1050
  • Quenching 
  Oil, Vacuume
Tempering temperature ºC 2x2 hrs
Hardness achieved ( HRC )
200
        53
 300
        52
 560
        50
 600
        40
  • Application 

 For Camera,sunglasses lenses/medical containers,disposable cutlery and containers, PVC,acetates, storage containers

                              
CARMO
  • Colour Code    
  Red / Voilet
  • Typical Analysis
C
  0,60
       Mn     
  0,8
       Cr      
  4,5
           Mo         
  0,5
        V        
  0,2
         Si        
  0,35
        Others
  --
  • Hardness Supplied approx.HB
   250
  • Standards
       AISI (USA)     --
       W.nr (Germany) 
   1.2358
       JIS (Japan) 
   --
  • Characteristics  
 A prehardened steel especially suitable for car body dies. 
  • Soft Anneal ºC
  860
  • Hardening Temp.ºC
   950-970
  • Quenching 
   Oil, Vacuum, air
  • HRC at tempering temperature ºC 2x2 hr
200
  59
250
  58
400
  57
500
  53
550

  50
600
  43
  • Application
   --

SVERKER 21 (HCHCr)

  • Colour Code    
  Yellow / White
  • Typical Analysis
C
  1,55
       Mn     
  0,4
       Cr      
  11,8
           Mo         
  0,8
        V        
  0,8
         Si        
  0,3
        Others
 --
  • Hardness Supplied approx.HB
   210
  • Standards
       AISI (USA)     D2
       W.nr (Germany) 
   1.2379
       JIS (Japan) 
   SKD 11
  • Characteristics  
 High performance tool steel with high wear resistance & toughness.
  • Soft Anneal ºC
  850
  • Hardening Temp.ºC
   990-1050
  • Quenching 
   Vacuum, air
  • HRC at tempering temperature ºC 2x2 hr
200
  63
250
  59
400
  59
500
  60
550

  54
600
  48
  • Application
 Tools for blanking, punch and die & trimming. Also for bending, deep   drawing & coining.

SVERKER 3 (HCHCr)

  • Colour Code    
  Red
  • Typical Analysis
C
  2,05
       Mn     
  0,8
       Cr      
  12,7
           Mo         
  --
        V        
  --
         Si        
  0,3
        Others
  W 1.1
  • Hardness Supplied approx.HB
   240
  • Standards
       AISI (USA)     D6
       W.nr (Germany) 
   1.2436
       JIS (Japan) 
   SKD 2
  • Characteristics  
 High performance tool steel with high wear resistance & toughness.
  • Soft Anneal ºC
  850
  • Hardening Temp.ºC
   920-1000
  • Quenching 
  Vacuum, air
  • HRC at tempering temperature ºC 2x2 hr
200
  64
250
  61
400
  60
500
  59
550

  56
600
  48
  • Application 

Tool for blanking, punching of thin section. Also for deep drawing,   bending & coining.

SLEIPNER

  • Colour Code    
  Blue/Brown
  • Typical Analysis
C
  0.9
       Mn     
  0.5
       Cr      
  7.8
           Mo         
  2.5
        V        
  0.5
         Si        
  0.9
        Others
  --
  • Hardness Supplied approx.HB
   235
  • Standards
       AISI (USA)     --
       W.nr (Germany) 
   --
       JIS (Japan) 
   --
  • Characteristics  
 A Cr-Mo-V alloyed tool steel with good chipping resistance & high   compressive strength.
  • Soft Anneal ºC
  850
  • Hardening Temp.ºC
   950-1080
  • Quenching 
   Gas, Vacuum
  • HRC at tempering temperature ºC 2x2 hr
200
   60
 300
  59
 560
  60
 600
  48
  • Application
 Sleipner is versatile steel for cold work tooling, with special  emphasis on abrasive wear.  It is recommended for medium run tooling applications.

VANADIS 4
  • Colour Code    
  Green/White
  • Typical Analysis
C
  1,50
       Mn     
  0,4
       Cr      
  8,0
           Mo         
  1,5
        V        
  4,0
         Si        
  1,0
        Others
  --
  • Hardness Supplied approx.HB
   230
  • Standards
       AISI (USA)     --
       W.nr (Germany) 
   --
       JIS (Japan) 
   --
  • Characteristics  
A Cold work tool steel producedby powder metallurgy process.Superiorcombination of toughness & wear resistance.  
  • Soft Anneal ºC
  900 
  • Hardening Temp.ºC
   980-1100
  • Quenching 
   Air, Vacuum
  • HRC at tempering temperature ºC 2x2 hr
200
  60
250
  58
400
  60
500
  61
550

  55
600
  47
  • Application 

Blanking, deep drawing & forming of Ms, Cu, Al & Austenitic SS.

VANADIS 10
  • Colour Code    
  Green/ Violet
  • Typical Analysis
C
  2,9
       Mn     
  0,5
       Cr      
  8,0
           Mo         
   1,5
        V        
  9,8
         Si        
  1,0
        Others
  --
  • Hardness Supplied approx.HB
   275
  • Standards
       AISI (USA)     --
       W.nr (Germany) 
   --
       JIS (Japan) 
   --
  • Characteristics  
  A Cold work tool steel produced by powder metallurgy process characterized   by extremely good abrasive wear resistance & high toughness.
  • Soft Anneal ºC
  900
  • Hardening Temp.ºC
   980-1100
  • Quenching 
   Air, Vacuum
  • HRC at tempering temperature ºC 2x2 hr
200
  63
250
  62
400
  61
500
  65
550

  60
600
  52
  • Application 

Blanking, deep drawing & forming of Ms, Cu, Al & Austenitic SS.